Monday, 12 December 2016

Love Seat Rehab

img_2429

So I have this lounge suite set in my stash that I don't mind the shape of but ugh.. the fabric makes my eyes hurt... lol

I decided something had to be done!.. I chose the 2 seater/love seat as my guinea pig (I've shown the 3 seater above because I forgot to take a picture of the 2 seater before I pulled it apart.)

The fabric was glued down within an inch of it's life so I put the piece in the microwave for 10 seconds to loosen it up. It worked but there was soooo much glue!

Here is a picture of the pieces after the sofa had been deconstructed and after I had painted the main wood pieces with primer. I did this because I would be using a lighter fabric and didn't want the wood to show through and/or leech into the fabric over time.

img_2430

During deconstruction some of the cushion foam got destroyed so I had to piece in some new foam so as not to have a lumpy sofa! This foam was part of the packaging in another piece of furniture's box. NEVER through these kinds of packaging materials away!... You never know when you might need
them. :)

img_2431

New foam pieced in.

img_2432

I cut out all my fabric for each piece before starting the process. Making sure to cut a little larger than each piece to allow for folding over to cover seams. Planning is key in this stage as you need to know how you are going to reconstruct the sofa and plan you fabric placement and size required appropriately. You also need to know which cushions you will be using in which location and facing in which direction so you can make sure that the fabric all faces the same way and that you have enough overhang to do the job you want it too.

Now to cover the cushions making sure to have the "grain"of the fabric facing the same way and making sure that it is sitting straight on the pieces where it will show. Regular Tacky Glue will do the job.

img_2433

Cut the corners and fold like a present.

img_2448

The base cushions were completely covered and glued on all four sides the back cushions were left open on two sides because they would wrap over the top and side of the couch during reassembly. You can see a completed seat cushion below bottom left and the two back cushions top right. The fabric you see beside the back cushions is the armrest fabric.

img_2437

Then on to the arms.

I had to sand a lot of glue of of the front of the arms before starting as it would have made them lumpy if I left it on. I also noticed when I held them together that who ever manufactured these chairs used two different sized dowels for the armrests! lol

img_2440

For the arms I first covered the front... I was careful not to pull the fabric too tight so that the "grain"stayed as straight as possible. I cut the fabric a bit larger than the arms and wrapped it around the sides. I cut little pizza wedges out of the excess to get a good fit around the round portion.

img_2439

I made a hem on the front face of the arm rest fabric for a clean finish. Then I folded the armrest fabric around the arm with enough of an overhang to cover the side of the base and be folded and glued underneath and out of sight.

img_2443

On to the base.

I cut enough fabric to go all the way around the base piece from top front to bottom to back. I know a lot of this area will be covered by cushions or other fabric pieces but just in case there are any gaps, this will make them less obvious.

I started by gluing the front of the back with enough over hang to fold over for a neat finish.

img_2444

Then I continued down the seat, taking extra care with the base front as this will be very visible on the finished product.

img_2436

And then across the bottom. It's important to cover the bottom because you don't want a beautiful upshot photo or view to be ruined by the sight of an unfinished sofa bottom.

I folded the base sides like a present. Cutting away excess fabric at the corners.

img_2446

I left the back unglued as this will be the last piece to be attached during reassembly.

img_2447

The next step was to attach the back cushions.

img_2451

Remember I left the top and side open? This is why. They are attached over the back and side of the sofa. This will give a clean finish from the top and side view once the back cover is on.

img_2449

Side view.

img_2450

Front view so far. :)

img_2451

Second back cushion attachment. Top done first. Side still to be glued.

img_2454

Both back cushions on.

img_2455

Now to attach the arms. As I said earlier. The side panel is attached all the way down the side to the bottom.

img_2456

img_2457

Now the seat cushions get glued in.

img_2458

And finally with the last arm glued in and the back piece glued on (with hems on all three sides for a clean finish.)

I added a bit of twine as piping at the point where the seat cushions & the base meet just to tidy it up a bit. A major improvement, no?

img_2459

With the legs put back on we have a final product!

img_2466

No comments:

Post a Comment